Machine Test CASSY 0.3

LD 7731901
Machine Test CASSY 0.3
Machine Test CASSY 0.3
Machine Test CASSY 0.3

Description

 The Machine Test CASSY is part of the machine test system for the analysis of electrical drives and the simulation of machine loads. Its compact size allows it to be used in an experiment demonstration panel rack or as a table top unit.

The Machine Test CASSY differs from its previous model in that it has an additional LAN connection. 

In addition to the control unit for the Electrical Dynamometer (773 2991), it has a powerful measurement and analysis system with four isolated and potential-free measurement channels. Each of those, each for simultaneous measurement of current and voltage, comparable to the Power Analyser CASSY (727 101).

  • The speed measurement is carried out via an optical sensor and gives an angular resolution of 0.1 °.
  • The torque is measured up to ±10 Nm with a resolution of 1x10-3 Nm. This can then also be calibrated with a reference weight of 1 kg.

The machine test CASSY can be used for the following experiments, as well as others:

  • Analysis of machines as a motor and as a generator
  • Behaviour to different load cases, e.g. flywheel mass, blower etc.
  • Behaviour of time variable load cases
  • Study of frequency converter with asynchronous machine, IMP machines
  • Starting induction machines and slip ring rotors with star-delta connection, soft starter and frequency converter,

The Machine Test CASSY differs from its previous model in that it has an additional LAN connection.

Machine selection:

It is possible to comprehensively parametrize all available machines. This parametrization is supported by intelligent menu guidance. Due to integrated recognition of machine types of new design this selection is eased.

Furthermore, machines from the existing inventory can also be integrated and individually parametrized. A switch-over of the safety loop between LD machines and e.g. machines of the brand "ELWE Technik" is easily possible.

The menu "Freely parametrizable" additionally allows the manual input of parameters of older machines, third-party machines or special machines e.g. for research purposes. Please contact our technical consultants.

Operating mode:

Testing of motors

The control during the testing of motors is either done by the measured speed or with the help of the measured torque.

  • Speed control: Manual, Automatic, Run-up characteristic, Load characteristic
  • Torque control: Manual, automatic dynamic unloading, automatic dynamic loading, automatic static according to IEC 60034-2-1 in 6 steps and additionally in 16 steps from 0 % to 150 %

Testing of generators

Electrical machines can be tested, monitored and analysed by the system as a generator in isolated operation - but also in mains operation.

Load simulation

Depending on the speed for start-up and operating behaviour.

  • Load characteristic: T(n) (extruder)
  • Load characteristic: T(n²) (turbomachine e.g. fan)
  • Load characteristic: TL = const. (elevator, crane)
  • Load characteristic: P const. (lathe, milling machine spindle)
  • Load characteristic: T(α) Flywheel mass
  • Load characteristic: Sum of load function

Time-dependent load

  •  Sine function , Trapezoid function , Delta function: 
  • Free functions, specified via external software, e.g: CASSY Lab 2 for Drives and Power Systems 524 222,

Generator control

Isolated operation

  • Power control with Voltage droop
  • Voltage control with power droop

Mains operation

  • Frequency-power control with droop
  • Voltage-reactive power control with droop
  • Parallel operation of generators

Mechanical analyses on machines

Moment of inertia

  • Determining the moment of inertia
  • Mechanical losses

Additional information:

  • Mains voltage: 230 V 50–60 Hz
  • Connected load: 1600 VA
  • Temperature controlled active ventilation
  • Dimensions: 500 mm x 300 mm x 180 mm
  • Mass: 10 kg

Technical data

Measurements in the range of the machine test system:

  • Speed: nM  in min-1 ±2000.0 , ±3500.0  , ±5000.0  , in s-1 34.00 , 64.00 , 84.00 ,
  • Torque: TM ±10.000 Nm
  • Angular acceleration: ωM in  °/s²  ±400,  ±4000 ,  ±40000 °
  • Mechanical power: Pmec in W ±200, ±600, ±1200 
  • Electrical power: Pel in W ±600, ±1200, ±1800 
  • Machine voltage: UM average terminal voltage in V DC ±36 , ±150 , ±360 , ±700 , AC 25 , 100 , 250 , 490 
  • Machine current: IM mean conductor current in A DC ±1, ±2.4 A, ±10.0, ±24.0, AC 0.7, 1.6, 7, 16
  • Power factor angle: φM
  • Mains frequency: fM
  • Excitation voltage: UE in V DC ±36, ±150, ±360, AC 25, 100, 250
  • Excitation current: IE in A DC ±1, ±2.4, ±10.0, ±24.0, AC 0.7, 1.6, 7, 16
  • Excitation power: PE ±400.0 W
  • Apparent power: SM in VA ±900.0, ±1800.0, ±3600.0
  • Reactive power: QM in var ±600.0, ±1200.0, ±3000.0
  • Efficiency: ηM 200.00 %
  • Slip: sM

Integrated didactic measurement system:

  • Inputs: 4 isolated measurement channels CAT III 300 each with I and U measurement (max. 8 can be used simultaneously)
  • Input A-D: U and I connection via 4 mm safety sockets
  • Measuring ranges U: 25 /70/250/700 V AC ±36 /±100/±360/±1000 V DC
  • Measuring ranges I: 0.7/1.6/7/16 A AC ±1/±2.5/±10/±16 A DC
  • Simultaneous measurement of U, I, φu, φ, f and P each in 4 channels as well current
  • Sampling rate max. 1,000,000 values/s per channel for U and I max. 500,000 values/s
  • Instantaneous and averaged values U, I and P, RMS values (AC+DC) U and I

Additionally included:

Basic wave filter, one analogue output, one Anlog input, one digital input, temperature monitoring for dynamometer and DUT, monitoring of shaft coverage, four-quadrant display and highest safety standard with leakage current < 5 mA.

Integrated operating and display unit

  • Display on 9cm colour screen (QVGA 3.5")
  • Display of all measured values can be done individually, channel by channel or in tabular form.
  • Display and evaluation of the measured values in different diagrams
  • Display of a vector diagram
  • Display of all parameters for control and configuration - also for operation without computer
  • Push button and incremental encoder with push button
  • Further functions and interfaces

USB type C interface and LAN connection via Ethernet (RJ-45 socket) with PC or laptop for use with specified via external software, e.g.: CASSY Lab 2 for drives and energy systems (524 222), LabView or MATLAB or as USB drive for transferring measurement data and for parameterisation.

Wireless (Wi-Fi) and LAN network for use with LabDoc or as an interface to Matlab and LabView.

 

Scope of delivery

  • Machine Test CASSY
  • 1x USB C / A cable
  • Cold device cable EU / GB
  • 7-pole conductor with round plugs

Related Documents

PDF (Instruction Sheet) PDF (Instruction Sheet) [773 1901] Machine Test CASSY 0.3

Downloads

Web Link Web Link CASSY.App Web
ZIP ZIP Mobile Config, Mobile Edit and Machine Test CASSY Firmware (V1.10)
Utilities and firmware update without CASSY Lab 2
MSI MSI CASSY Lab 2 for Drives and Power Systems (en, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (fr, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (es, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (pt, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (it, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (nl, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (ru, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
MSI MSI CASSY Lab 2 for Drives and Power Systems (zh, V2.29)
Free demo version, full version requires a licence code of CASSY Lab 2 for Drives and Power Systems
Manual Manual CASSY Lab 2 Manual (en)
Manual Manual CASSY Lab 2 Manual (fr)
Manual Manual CASSY Lab 2 Manual (es)
Web Link Web Link CASSY Lab 2 Web Help (en)
Web Link Web Link CASSY Lab 2 Web Help (fr)
Web Link Web Link CASSY Lab 2 Web Help (es)
ZIP ZIP CASSY SDK for own software development (Windows/Linux)
ZIP ZIP LabVIEW driver for LabVIEW 2017 or higher (Windows)
ZIP ZIP MATLAB driver with examples (Windows)
Print page

Contact Us

Technical Service & Support:

Online Service Portal
Do you have any questions or suggestions regarding our devices, products, experiments, equipment sets or about our software? You need spare parts? FORM

Repair Service
You would like to register a repair? FORM

Europe
For European distributors, please visit: European distributors
Worldwide requests
Please contact us per email: sales@ld-didactic.de

 Click here for our contact form and postal address.

Contact Us